Greenheck Microprocessor Controller (475595 IOM) TAP v2.10 A Manual de usuario descargar pdf (Pagina 23)

F. Board Switch

The Board Switch menu allows the user to jump between different controllers with

a remote display. This requires a remote display, along with additional controllers,

set-up in a pLAN network. A pLAN can consist of up to 32 devices, in different

combinations, but a maximum of 31 controllers.

WHEN VIEWING THIS SCREEN FROM A REMOTE DISPLAY, THE USER IS ABLE TO CHANGE

WHICH CONTROLLER’S MENU SHOULD BE DISPLAYED.

Unit Address: The pLAN address of the controller the display is currently

accessing.

Switch to unit: The pLAN address of the controller the display would like to

access.

Board Switch

Unit Address: 1

Switch to unit: 1

1. . . . . . . . . . 16

17 . . . . . . . . . 32

To manually override a control loop, the unit must be ON. In each respective

screen, change the control from AUTO to MANUAL.

To resume normal operation after overriding the controller, simply cycle power to

the unit.

Control Loop Overrides

Unit must be ON.

To resume normal operation,

cycle unit power.

THIS SCREEN ALLOWS THE USER TO OVERRIDE THE ENERGY WHEEL OPERATION.

This screen only appears if the unit is equipped with a non-VFD operated energy

wheel.

When the Wheel Control is in the MANUAL mode, use the arrow buttons to turn

the wheel ON or OFF.

Energy Wheel Override

Wheel Control: Auto

Wheel: OFF

The Overrides menu is for start-up, commissioning and troubleshooting. This

menu allows the user to override the control loops and specific inputs and

outputs. To access the Overrides sub-menus, enter the service password

(Default=1000). Caution: overriding components and I/O can be dangerous to the

equipment. Always cycle power to the unit when finished with the override.

G. Service

b. Overrides

a. Analog Inputs

b. Digital Inputs

c. Relay Outputs

d. Analog Outputs

e. Control Loops

Code: Controller setup code determines functionality of program. When

contacting the factory, please reference this code.

Ver: Displays the current program version and data code of the current program.

Manual: The manufacturer part number for the corresponding Installation,

Operation and Maintenance (IOM) Manual.

Information

Greenheck Fan

Code: GWY1X000XXXX

Ver.2.10 4/1/14

Manual: 475595

Bios: 5.18 11/17/10

Boot: 4.03 07/03/06

G. Service

The Service menu allows the user to access several sub-menus regarding controller

information, controller overrides, operating hours, BMS configuration, I/O manual

management and Probe Adjustment. The user can also change the default Service

Password (1000) by accessing the Service Settings sub-menu. By accessing the

BMS Config sub-menu, the user can adjust BMS protocol settings. (BACnet®,

LonWorks®, Modbus®)

ENTERING THE INFORMATION SUB-MENU WILL DISPLAY INFORMATION ABOUT THE

CONTROLLER AND THE PROGRAM LOADED ON THE CONTROLLER.

G. Service

a. Information

Analog Input

Outside Temperature

Manual Control B005: OFF

Manual Position 0.0

Value 73.5

THIS SCREEN IS AN EXAMPLE OF A MANUALLY MANAGED TEMPERATURE ANALOG INPUT.

To manually control an analog input, change Manual Control to ON. Move cursor

to Manual position and alter value. The altered value will be displayed below.

Similar screens exist for the remaining I/O. To resume normal operation, simply

cycle power to the unit. Contact the factory for more details.

DDC Controller for Tempered Air Products

1 2 ... 18 19 20 21 22 23 24 25 26 27 28 ... 43 44

Comentarios a estos manuales

Sin comentarios

Greenheck Microprocessor Controller (475595 IOM) TAP v2.10 A Manual de usuario Pagina 23

Comentarios a estos manuales

Relacionado con productos y manuales para Equipo Greenheck Microprocessor Controller (475595 IOM) TAP v2.10 A