Greenheck Microprocessor Controller (475595 IOM) TAP v2.10 A Manual de usuario descargar pdf (Pagina 26)

THIS SCREEN ALLOWS THE USER TO ADJUST BACNET IP PARAMETERS.

This screen only appears if the selected BMS protocol is set to BACnet IP/Eth and

BACnet Plugin = YES.

If a BACnet IP card has been installed, the default parameters can be changed

via the controller display. The card is in DHCP mode from the factory. Once

communication is established, the user can enter static IP parameters.

To view current parameters:

1. Power on controller and allow several minutes to initialize.

2. Go to BMS Config menu and view BACnet Read/Write screen.

3. Change Function to Read and Update? to YES.

TCP/IP SETUP

Instance: 77000

IP set by: DHCP

IP: 128.2.104.134

Subnet: 255.255.000.000

Gatewy: 128.2.0.12

TCP/IP SETUP

DNS 1: 193.168.001.001

DNS 2: 193.168.001.001

Type: IP

THIS SCREEN ALLOWS THE USER TO ADJUST BACNET MSTP PARAMETERS.

This screen only appears if the selected BMS protocol is set to BACnet MSTP and

BACnet Plugin = YES.

If a BACnet MSTP card has been installed, the default parameters can be

changed via the controller display. Factory settings are shown in the screen to the

left.

To view current parameters:

1. Power on controller and allow several minutes to initialize.

2. Go to BMS Config menu and view BACnet Read/Write screen.

3. Change Function to Read and Update? to YES.

Current BACnet MSTP parameters should now be displayed in the BACnet MSTP

SETUP screen. If all values appear to be zeros, consult the factory. (Make sure

you have allowed several minutes for the controller to initialize). *Values may

appear to be zero prior to setting the Function to READ.

To change BACnet MSTP parameters:

1. Power on controller and allow several minutes to initialize.

2. Go to BMS Config menu and view MSTP SETUP screen.

3. Move cursor to desired parameter by pressing the

buttons. Press

to select the parameter to change. Press the

buttons to adjust the

parameter. Press to save adjusted value.

4. Once desired parameters have been entered, go to BACnet Read/Write

screen. Change Function to Write and Update? to YES.

5. Reboot the controller by cycling power to the unit. Allow several minutes for

the controller to initialize.

6. View MSTP parameters. If changed values did not save, contact the factory.

MSTP SETUP

Instance: 77000

Baudrate 38400

MAC Addr: 0

MaxMasters: 127

MaxInfoFrames: 20

BACnet Read/Write

Function: Read

Update? Yes

*Cycle unit power to confirm

write command.

THIS SCREEN ALLOWS THE USER TO ADJUST MODBUS PARAMETERS.

This screen only appears if the selected BMS protocol is set to Modbus.

The address is the Modbus address of the card installed in the SERIAL CARD

port located on the face of the controller. (Factory Default Address = 1).

MODBUS SETUP

Address: 1

Baudrate 9600

Stop bit: 2

Parity mode: NONE

THIS SCREEN ALLOWS THE USER TO SELECT THE BMS PROTOCOL. ALL BMS

PROTOCOLS REQUIRE A COMMUNICATIONS CARD INSTALLED IN THE SERIAL CARD

PORT, LOCATED ON THE FACE OF THE CONTROLLER.

If the protocol is BACnet MSTP or BACnet IP/Eth, the user can change common

BACnet parameters via the controller. The BACnet Plugin must be set to YES.

BMS Conﬁguration

Protocol: BACnet MSTP

BACnet Plugin? YES

The BMS Config menu allows the user to view and alter BMS protocol settings.

If the BMS protocol is BACnet or Modbus, additional screens allow further

configuration. See below for details. To access the BMS Config sub-menu, enter

the service password (Default=1000).

G. Service

c. BMS Config

DDC Controller for Tempered Air Products

1 2 ... 21 22 23 24 25 26 27 28 29 30 31 ... 43 44

Comentarios a estos manuales

Sin comentarios

Greenheck Microprocessor Controller (475595 IOM) TAP v2.10 A Manual de usuario Pagina 26

Comentarios a estos manuales

Relacionado con productos y manuales para Equipo Greenheck Microprocessor Controller (475595 IOM) TAP v2.10 A